{"title":"JA-80Q","description":"\u003ch2 style=\"text-align: justify;\"\u003eService explanation for JA-80Q\u003c\/h2\u003e\r\n\u003ch3 style=\"text-align: justify;\"\u003e1 Installation in the control panel\u003c\/h3\u003e\r\n\u003cp style=\"text-align: justify;\"\u003e\u003cbr\u003e\u003cstrong\u003eImportant: Hardware compatibility with the JA-80K control panel is from hardware version KE10104. Check the description on the main board of the control panel. (the version number is printed right next to the RESET jumper.)\u003c\/strong\u003e\u003cbr\u003eIf you purchased the module separately, it must be installed in the Oasis control panel as follows:\u003cbr\u003e1. The central unit must be completely disconnected from electricity (both 230V and the battery)\u003cbr\u003e2. Plug the JA-80Q module (in the control panel) into the digital bus connector designed for the (standard) JA-80Y connection\u003cbr\u003e3. For parallel use of a JA-80Y module, insert the plug of the dialer into the socket of the JA-80Q module.\u003cbr\u003e \u003cimg src=\"http:\/\/www.pg-securitysystems.nl\/images\/afbeelding%2025.jpg\" width=\"380\" height=\"240\"\u003e\u003c\/p\u003e\r\n\u003ch3 style=\"text-align: justify;\"\u003e2 Learn detectors with camera\u003c\/h3\u003e\r\n\u003cp style=\"text-align: justify;\"\u003e\u003cem\u003eInstallation may only be performed by a certified technician approved by an authorized distributor.\u003c\/em\u003e\u003cbr\u003e1. Place the central unit in service mode and press the 1 key on the control panel to activate the learning mode (see description of the central unit).\u003cbr\u003e2. Learn the JA-84P by inserting its battery (see description of the JA-80P)\u003cbr\u003e3. Exit the central unit's enrollment mode.\u003cbr\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e If the detector was already enrolled in the control panel before the JA-80Q module was installed, you do not need to re-learn the detector. You only have to activate the learning mode and exit again. In this way the module will obtain all relevant information from the control panel\u003c\/p\u003e\r\n\u003ch3 style=\"text-align: justify;\"\u003e3 Programming the dialer\u003c\/h3\u003e\r\n\u003cp style=\"text-align: justify;\"\u003eFor successful transmission to the web server that has a photo receiver program, the server IP address must be programmed into the JA-80Y or JA-80V dialer. The address of the Jablotron photo display website is \u003ca href=\"http:\/\/img.jablotron.com\" target=\"_blank\"\u003e\u003cspan style=\"text-decoration: underline;\"\u003ehttp:\/\/img.jablotron.com\u003c\/span\u003e\u003c\/a\u003e.\u003cbr\u003eIP address is: 77.104.20.129 port 7070\u003c\/p\u003e\r\n\u003cp style=\"text-align: justify;\"\u003e1. Place the control panel in service mode.\u003cbr\u003e2. Program the required IP address and port to be used to send the data to with the ComLink program (in the ARC window) or by entering the following sequence.\u003cbr\u003e\u003cstrong\u003e013 *8 xxx xxx xxx xxx yyyyy *0\u003c\/strong\u003e\u003c\/p\u003e\r\n\u003cp style=\"text-align: justify;\"\u003eWhere: \u003cbr\u003e\u003cstrong\u003exx..x\u003c\/strong\u003e is the 12 digit IP address\u003cbr\u003e\u003cstrong\u003ey..y\u003c\/strong\u003e is the 5 digit port number of the receiver. See also the description of the\u003cem\u003e voter.\u003c\/em\u003e\u003cbr\u003e\u003cem\u003e  Example:\u003c\/em\u003e 013 *8 077.104.220.129 07070 *0\u003cbr\u003e3. Exit the control panel's service mode.\u003c\/p\u003e\r\n\u003cp style=\"text-align: justify;\"\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e\u003cbr\u003e\u003cstrong\u003eThe setting or change to the setting is only active when the control panel is taken out of service mode.\u003c\/strong\u003e\u003cbr\u003eThe information about a new photo via SMS is sent to all telephone numbers that also receive the event \"burglary alarm – immediately\". This SMS also contains a link to the new photo on the server. This option is available on the JA-80Y from software version number XA61009 and on the JA-80V from software version number XA64005.\u003c\/p\u003e\r\n\u003ch3 style=\"text-align: justify;\"\u003e4 LED signals\u003c\/h3\u003e\r\n\u003cp style=\"text-align: justify;\"\u003eAfter taking a photo of a detector, the photo will be sent to the control panel and then to the JA-80Q module via the digital bus. This is indicated by a green flashing LED. Successful transmission is confirmed by a long green flash (2 sec). Failed transmission is indicated by a series of rapid green flashes at the end.\u003cbr\u003eOnce the photo has been received by the JA-80Q module, the photo is sent via the dialer to the pre-programmed web server. This transmission is indicated by a flashing red LED on the JA-80Q module. Successful transmission is confirmed by a long red flash (2 sec). Failed transmission is indicated by a series of rapid red flashes at the end.\u003cbr\u003eThe total time taken from the moment the photo is taken until it is received on the web server is approximately 20 seconds. With a weak signal, delays may occur (because the data is sent multiple times). Each photo has a date and time indication (copied from the control panel) when it was taken. It takes at least 60 minutes from the moment of connection before the time of the photos is synchronized with the central unit.\u003c\/p\u003e","products":[],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0937\/8860\/2689\/collections\/jablotron-ja-80q-foto-module1.jpg?v=1761583481","url":"https:\/\/www.alarma-total.es\/en\/collections\/ja-80q.oembed","provider":"Alarma-Total.es","version":"1.0","type":"link"}