Jablotron modules
Jablotron modules
-
Jablotron JA-120Z BUS extender 500m
JA-120Z BUS extender 500m Suitable for current stimulation of the bus, extension of the line length and galvanic isolation of the bus.The JA-120Z extends the BUS line by no less than 500m per terminal. 3 modules can be placed in series, allowing a total of 2000m to be bridged. The kit consists of: a circuit board for the JA-120Z module and a JA-83PWR power source. The backup battery and plastic housing must be purchased separately.* Output current max. 2A* 2 independent bus output terminals – each provides 500 m bus lengthThe product is offered as an electronic module with power supply unit JA-83PWR. We recommend installing the product in a plastic housing PLV-CP-L. The product is a component of the JABLOTRON 100 system, is addressable and occupies one position in the system.* The galvanic isolation of the output terminals serves for different ground potentials and the protective insulation of the bus* Up to 3 boosters can be arranged in series* Backup battery up to 18 Ah
€557,27
-
Jablotron JA-110N-DIN BUS DIN current output power module
Jablotron JA-110N-DIN BUS DIN current output power moduleThe Jablotron JA-110N-DIN BUS DIN current output power module is designed for a DIN rail. The module supplies power to the relay output. It can be used, for example, to control lights, fans, etc. The relay output is programmable via the control panel.• Power supply 12 V bus (9 ... 15 V)• Power consumption during backup (relay open / closed) 5 mA / 45 mA• Power consumption for cable selection 45 mA• Rating relay (galvanically isolated) - Class II:• Maximum switching voltage 250 V AC / 24 V DC• Resistive load (PF = 1) max.16• Inductive, capacitive load (PF = 0.4) max 8A• Halogen lighting max. 1000 W DC 384 W• Minimum DC switching 0.5W• Twisted wires 2 x 1.5 mm2 max 1 x 2.5 mm2• Dimensions 18 x 90 x 64 mm• General indoor environment• Temperature, -10 To + 40 ° C• Housing IP-20• Complies with EN 50130-4, EN 55022, EN 60950-1 DIN rail EN60715
€119,89
-
Jablotron JA-114HN BUS connection module with 4 inputs and outputs
Jablotron JA-114HN BUS connection module with 4 inputs and outputsA bus module, containing four wired inputs with adjustable EOL resistance values, four galvanically isolated signal PG outputs and an additional power supply, protected by an electronic fuse. In addition to the EOL type resistor, the values of resistors can also be set for the inputs. The outputs are designed as galvanically isolated units (two each have a common C terminal). The module occupies four positions in the control panel and is equipped with one tamper sensor at the front and one at the back.It is especially suitable for the renewal of wired alarms, where old detectors are used. They are also very commonly used to control multiple devices through the PG outputs. The auxiliary power supply makes it possible
€202,41
-
Jablotron JA-192Y GSM dialer for Jablotron Pro Centrales
Jablotron JA-192Y GSM dialer for Jablotron Pro Centrales The control panel equipped with a JA-192Y communicates via a mobile network with a central monitoring station, enables control and mobile applications via the web and sends alarm SMS messages and voice messages. This allows the system to be set up remotely using the settings of the F-Link program.
€288,86
-
Jablotron JA-110Z-D Multipositional bus contact module
Jablotron JA-110Z-D Multipositional bus contact module This module is designed to connect the conductors of complex bus installations of the JABLOTRON 100 system. It can be divided into two independent bus branches by disconnecting jumpers.It can be installed in the junction box JA-194PL, PLV-CP-M / L or directly in the central JA-106K.Product Info
€33,01
-
Jablotron CT-01 Roller shutter detector
Jablotron CT-01 Roller shutter detector The CT-01 is a wired detector intended for detecting the unauthorized movement of external shutters on houses or buildings. This detector is hardwired and can be connected with JA-150M or JA-81M to continue communication wirelessly.By using this detector it is possible to optimally protect the building against intruders. When the shutters are forced, this will be detected and the alarm can respond. Even before the intruder gets in! False alarms caused by the wind, which causes the shutters to move only slightly, are avoided because the alarm only occurs when at least 3 pulses are received within 5 seconds.Product Info
€45,59
-
Jablotron JB-110N Pro Bus PG power output module
Jablotron JB-110N Pro Bus PG power output module The product is a system device for the Jablotron Midway Pro and Essex Pro. It provides a switching contact for the output power relay. For example, it can be used to control lighting, fans, etc. The relay communicates via the bus and is powered by the control panel bus. It can be installed in a JA-19xPL installation box or a control box.
€82,53
-
Jablotron JB-118N Pro Bus signal PG output module – 8 outputs
JB-118N Pro Bus signal PG output module – 8 outputs Key features: The product is a system device for the Jablotron Midway (Pro) and Essex (Pro) The outputs are isolated from the bus It is set using the DIP switch The device is not addressable (it does not occupy a position in the security system)
€119,88
-
Jablotron JB-111N BUS signal output module PG
Jablotron JB-111N BUS signal output module PGThe Jablotron JB-111N BUS signal output module PG is designed to provide a changeable output delay (8 A) with a NO or NC setting. An appropriate PG output is controlled via DIP switches (controls 1 of 32 different DIP switches). The module communicates and is powered via the bus connection to the control panel. The JA-111N can be installed in the JA-190PL housing. This module does not occupy any additional space in the zone file.• Power supply: via the BUS of the central unit, 12V (9 - 15 V)• Power off power consumption: 5 mA• On power consumption: 25 mA• Maximum load of the relay output: maximum 1 A/30 V DC• Minimum switching current: 10 mA • Environment in accordance with EN 50131-1, EN 50131-3: II, indoor• Operating temperature: -10 to 40 °C
€74,29
-
Jablotron JA-191Y LTE, GSM 4G dialer for Jablotron 100, 101 and 106
JA-191Y LTE, GSM 4G dialer for Jablotron 100, 101 and 106The LTE-4G GSM module is intended for use with the JA-100K, JA-101K and JA-106K alarm control panels of the JABLOTRON 100+ series.
€474,73
-
Jablotron JA-112M, Bus module for magnetic contacts, 2 inputs
JA-112M, Bus module for magnetic contacts, 2 inputs Up to 100 m of wiring can be connected to each input Inputs can be connected without balancing They can be individually or dual balanced and can be connected to a roller blind switch function The module allows to invert the input or set the minimum activation time to enable the alarm (from 0.1 s to 300 s) The detector communicates with the control panel bus and is powered by this bus The detector is addressable and occupies two positions in the security system
€49,51
-
Jablotron JA-194Y, GSM 4G dialer for the JA-103K/107K
Main features:- 4G Chooser for the Jablotron 103K and 107K systems- Power source for the module 9-15 V DC (from the control panel)- Average power consumption 9 mA (depending on GSM signal strength)- Current power consumption 720 mA- 2G (GSM, EDGE) 900/1800 MHz GSM communication band- 3G 900/2100 MHz (B8, B1) GSM communication band- 4G (LTE) 800/900/1800/2100/2600 MHz (B20,B8,B3,B1,B7) GSM communication band- I&HAS classification Safety grade 2/Environmental class II- Dimensions/weight 70mm x 37mm x 25mm/23gr.- Operational environment General solution for internal use- Operating temperature -10°C to +40°C- Average operating humidity 75% RH, non-condensing- Compatible with RMT (ARC Receiver) According to communication protocols
€498,48
-
Jablotron JB-161N-PLUG, smart socket with LED indication
Smart, wireless, two-way communicating plugs represent a completely new solution for automation within the JABLOTRON 100+ system. The plug copies the selected PG output.
€149,33
You have 37 of the 37 products seen